---
title: "Cisco Admin - CyberData VoIPv2 Paging Amplifier"
slug: "cisco-admin-cyberdata-voipv2-paging-amplifier"
tags: ["calltower", "public"]
updated: 2026-09-18T14:29:03Z
published: 2026-09-18T14:29:03Z
canonical: "learn.calltower.com/cisco-admin-cyberdata-voipv2-paging-amplifier"
---

> ## Documentation Index
> Fetch the complete documentation index at: https://learn.calltower.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Cisco Admin - CyberData VoIPv2 Paging Amplifier

## Prerequisites

POE Power: You will need to either connect to a POE switch or have a POE Injector. Speaker: You will need a speaker.

![1.png](https://cdn.us.document360.io/4662144b-ab1f-4796-8b7b-e9f9c609894f/Images/Documentation/1(3).png?sv=2026-02-06&spr=https&st=2026-11-05T00%3A12%3A21Z&se=2026-11-05T01%3A12%3A21Z&sr=c&sp=r&sig=tlLRe%2FF2w9hpSoSnGJqMmtGMUqU75hEeCIgRmFcDxaM%3D)

### Paging Amplifier Components

![2.png](https://cdn.us.document360.io/4662144b-ab1f-4796-8b7b-e9f9c609894f/Images/Documentation/2(5).png?sv=2026-02-06&spr=https&st=2026-11-05T00%3A12%3A21Z&se=2026-11-05T01%3A12%3A21Z&sr=c&sp=r&sig=tlLRe%2FF2w9hpSoSnGJqMmtGMUqU75hEeCIgRmFcDxaM%3D)

### Procedure

Configure Dip Switch Settings Before connecting the Ethernet cable to the VoIP PA you need to adjust the Dip Switch Settings. You will need to remove the small cover on the side of the device to gain access to the dip switches.

![3.png](https://cdn.us.document360.io/4662144b-ab1f-4796-8b7b-e9f9c609894f/Images/Documentation/3(5).png?sv=2026-02-06&spr=https&st=2026-11-05T00%3A12%3A21Z&se=2026-11-05T01%3A12%3A21Z&sr=c&sp=r&sig=tlLRe%2FF2w9hpSoSnGJqMmtGMUqU75hEeCIgRmFcDxaM%3D)

1. On - Allows device to be powered using POE switch power.
2. Off - Manual Volume control
3. On - LP Mode
4. Off - AMP – Low

## Create a Phone

Add a common area phone in connect as a Third-party SIP Device with the following settings.

![4.png](https://cdn.us.document360.io/4662144b-ab1f-4796-8b7b-e9f9c609894f/Images/Documentation/4(3).png?sv=2026-02-06&spr=https&st=2026-11-05T00%3A12%3A21Z&se=2026-11-05T01%3A12%3A21Z&sr=c&sp=r&sig=tlLRe%2FF2w9hpSoSnGJqMmtGMUqU75hEeCIgRmFcDxaM%3D)Wait for Connect to show that the phone has been installed.

## Configure the PA (CyberData Paging Amplifer)

Once the PA is plugged into POE switch and powers up all the LED lights should go green except for the Link light, it will be amber. 1)Connect the speaker 2)Press Firmly and Release the RTFM button. It will announce the IP address of the device. 3)Open a web browser and navigate to the IP address. The default name and password are admin, admin. a)Navigate to the SIP Config Page and change the following. 1)SIP Server : (IP Address of Publisher) 2)BackUp SIP Server 1: (IP Address of a Subscriber) 3)BackUp SIP Server 2: (IP Address of the other Subscriber) 4)Select Option labeled : (Use Cisco SRST) 5)SIP User ID: (DN of Device) 6)Authenticate ID: (User Name) 7)Authenticate Password: (12345 – default password) 8)Re-Registration Interval:(120) 9)Press SAVE 10)Press REBOOT 11)Wait the 30 seconds for the device to reboot 12)You should now see a green (Registered) message for all servers. 13)Call the DN, you should hear a beep then you can page over the speaker ![Paging001.png](https://cdn.us.document360.io/4662144b-ab1f-4796-8b7b-e9f9c609894f/Images/Documentation/Paging001.png?sv=2026-02-06&spr=https&st=2026-11-05T00%3A12%3A21Z&se=2026-11-05T01%3A12%3A21Z&sr=c&sp=r&sig=tlLRe%2FF2w9hpSoSnGJqMmtGMUqU75hEeCIgRmFcDxaM%3D) Support Documentation Cyberdata Install Document – Install Support document. [http://www.cyberdata.net/products/vo..._Ops_Guide.pdf](https://www.cyberdata.net/products/) Connect to Cisco Call Manager as SIP Endpoint – Cisco setup Install guide [http://www.cyberdata.net/support/ser...P_Endpoint.pdf](https://www.cyberdata.net/collections/all)